Cardax FT Controller – Download as PDF File .pdf), Text File .txt) or read online. Installation Guide. Cardax FT Controller CAUTION This equipment contains components that can be damaged by electrostatic discharge. Ensure both you. The Gallagher Controller supports the following door readers: > Cardax IV Prox (Mifare, kHz, TIRIS). > Cardax IV Prox Plus (Mifare, kHz,. TIRIS).

Author: Voodoogis Kigacage
Country: Denmark
Language: English (Spanish)
Genre: Music
Published (Last): 15 December 2013
Pages: 61
PDF File Size: 2.44 Mb
ePub File Size: 8.58 Mb
ISBN: 768-6-47219-238-8
Downloads: 15029
Price: Free* [*Free Regsitration Required]
Uploader: Dushicage

Shimano tiagra flight deck 9 speed manual Acer travelmate lci driver Ni circuit design suite keygen Documents.

Open the Internet Browser. Follow the steps below to access the Controller’s Config web page: When using these connection points, ensure the Power Supply to the Cardax FT Controller is capable of supplying the extra current required. These contacts close when carda Controller cardzx powered up, and remain closed until either the power is removed or there is a ‘Catastrophic Failure’. Controller The Gallagher Controller is specifically designed to support access controlled doors and integrated intruder alarms.

The Gallagher Controllers are intelligent field controllers, programmed to make access control and intruder alarm decisions in the field, independent of the Gallagher Command Center.

The cables should stow neatly and be held in place by the cable clamps fitted into the base of the Cabinet. The Gallagher Controller is specifically designed to support access controlled doors and integrated intruder alarms.

Gallagher Controllers | AES Group Ltd.

The red Run LED flashes in the following sequence: Set switch 2 to OFF open. High Spec variant only The High Spec variant of the Controller has a secondary Ethernet connection link to which communications can automatically be switched upon failure of cagdax primary Ethernet connection. Switch off the power supply to the Cardax FT Controller. The cabling between GBUS devices should be done in a daisy chain or serial format, i. Revert to the factory default version of the operating system.


It is an Ethernet attached device which connects to a server, however it can operate autonomously. On-board termination is optional using termination jumpers. Card readers Intruder Alarms may be installed in elevator cars to Documents.

Cardax FT Version 5.

Published on Oct View 1. Wait for the Run LED to stop flashing. Install all the system and power cables. Purpose of this presentation This presentation introduces: The Cardax FT Cabinet should be installed in a secure, internal location. Looking at the Controller it will be obvious that the there is no ethernet activity on either ethernet connection, as the RJ45 connector LEDs will not be operating, and the Controllers run LED will be 600 2 flash.

Controller will reject WWW connections. Refer to the “Component layout” within this Installation Note for wiring this plug. On startup, the main application is run. Switch on power to the Cardax FT Controller The termination jumper on either GBUS circuit needs to be fitted if the Controller is the end device for this circuit.

Cardax Ft Controller pdf

The Cabinet door must remain closed for at least one minute for the initialisation of the optical tamper detectors to be completed. Assigning an IP address manually via a web browser When the Cardax FT Controller is started reset or power-up with DIP switches 2 and 3 enabled, the Controller uses the following default addresses: Refer to the previous section “Component layout” for the location of the plugs.


Both variants of the Controller caddax operate on their own, or can have an optional Reader Module part number C or C connected.

Alternatively, an override reset on the Controller can be carried out in Cardax FT Command Centre via the Status and Overrides tab of the Controller properties with the cabinet closed.

Install the component identification decal inside the Cardax FT Cabinet door. Before you beginShipment contentsCheck the shipment contains the following items: Changes or modifications not expressly approved by Gallagher Security Management Systems could void the user’s authority to operate this equipment.

Cardax Ft Controller 6000pdf

This port is provided for external communications to be connected to the system. This takes approximately 11 seconds, while data is being written to memory. On-board connections are provided for:.

When 60000 Controller has a Reader Module connected, it receives information from the Reader Module about access requests and instructs the Reader Module to carry out the required function. Key Strengths of Cardax FT 1. Cardax FT for Airport Security. The software is powerful,