Manuals and User Guides for Buderus Logamatic We have 4 Buderus Logamatic manuals available for free PDF download: Applications Manual, . Buderus. HYDRONIC SYSTEMS. Operating Instructions. Logamatic R The Logamatic R controls the entire system based on your specific heating. Logamatic Controls – Buderus Logamatic Control The Logamatic has the ability to control a boiler (V or dry contact), a pump or multi-.

Author: Fenrizahn Vigis
Country: Bhutan
Language: English (Spanish)
Genre: Photos
Published (Last): 24 January 2005
Pages: 264
PDF File Size: 6.82 Mb
ePub File Size: 14.30 Mb
ISBN: 825-1-61301-587-3
Downloads: 20888
Price: Free* [*Free Regsitration Required]
Uploader: Goltinris

logamztic The Thrill of Exceeding Expectations. I also called Buderus and spoke to one of their technical support guys. Table of contents Table Of Contents They normally keep the downstairs atthe upstairs at 59, and the zone over the garage at 55, which won’t come on unless they turn it to 61 to watch TV, because it gets enough heat from the other part of the zone due to the common returns.

The house can see rather high wind conditions, as it is on top of a hill, and the wind determines the heating load as much or more than the temperature. General Information On The Bfu I have logajatic through each of the three manuals and several threads on this web site and another heating forum, and I’ve figured some of it out, but I’m still working on a few concepts about how it works.

Buderus Logamatic 2107 Manuals

Xiphias, this seems contrary to your recommendation to use an indoor sensor. Creating A New Heating Program The estimator who recommended the Taco seemed to be VERY familiar with both units and said that he has installed lots of both. It will eventually hit WWSD anyway, so it’s probably best just buuderus leave it at the default? It doesn’t appear to be by the manual. Entering A Vacation Program As Trooper is fond of saying, the installation manual is not a kneepad!


Switching The Controls On Find all posts by NJT. Closing dampers in the other zones will reduce output.

Your browser has JavaScript disabled

Troubleshooting Domestic Hot Water Setback Heating Mode night Mode Personally, I would probably go right for the Logo Check out page 40 and beyond of the user manual: Recovery from setback actually takes a lot of juice with a hydronic system. Thank you all again! The variable speed pump is logamtaic for a 20F deltaT, which is the basic old buderuss from baseboard hot water systems. Right now at around 20FF, the system is running with hotter water than it really needs, such that the air handlers seem to be running less than they were at 40F.

It lights easily with no 207, burners with no oil line heater, prior to start-up the outside air cools the oil, therefore when the unit starts, you tend to have combustion problems.

As rbeck commonly points out, zoning can often lead to short-cycling of the boiler because with only one or two zones calling the boiler is way oversized for just the load of that small demand.


Setback Mode Selection Troubleshooting “no Heat” Call General Discussion Pro’s Forum: I ran it for one heating season on just the outdoor sensor, with a pretty-well calculated reset curve or so I thought. Building Science Discussions Pro’s Forum: Also, if going with the Logamatic, would I want both indoor logamati outdoor sensors?

Calling Up The Menu They have no need for it, as their system has Cryotek glycol in it for freeze protection of the attic air handler and piping.

And if you don’t like it, just disconnect it. And the third said that for my house the Taco PC would work better. Lots of big buildings do this, and have for years. The boiler vents to the chimney which is approx feet away. If it does, would it be useful for adjustments based on wind conditions, even though the actual degrees displayed may not end up meaning anything with hydro air, they would just become arbitrary reference buderua

Buderus Logamatic vs Taco PC – Community Forums

Room Temperature Offset Refer to eBay Return policy for more details. Then just quit entirely and have come to love it. Does the schedule setting do anything at all if it is set for 24 hour DHW production and buferus Changing The Operating Mode Key To Symbols